GP5810-16 Pizza Box 10G XG(S)-PON Combo OLT
Product Overview
GP5810-16 OLT is a highly integrated, large-capacity XG(S)-PON OLT for operators, ISPs, enterprises, and campus applications. The product follows the ITU-T G.987/G.988 technical standard, and can be compatible with three modes of G/XG/XGS at the same time.
The asymmetric system (up 2.5Gbps, down 10Gbps) is called XGPON, and the symmetric system (up 10Gbps, down 10Gbps) is called XGSPON. The product has good openness, strong compatibility, high reliability and complete software functions, together with the optical Network unit (ONU), it can provide users with broadband, voice, video, surveillance and other comprehensive service access. It can be widely used in operators' FTTH access, government and enterprise park access, campus network access, ETC. XG(S)-PON OLT provides higher bandwidth. In application scenarios, service configuration and O&M completely inherit GPON.
GP5810 is only 1U in height, easy to install and maintain, and save space. Supports mixed networking of different types of ONUs, which can save a lot of costs for operators.
Product Highlight
- Comply with ITU-T G.984/987/G.988 technical standards, with good connectivity capabilities
- Pon port can support GPON/XGPON/XGSPON three modes
- Rich Layer 2/3 switching features and Flexible management methods
- Support multiple link redundancy protocols such as FlexLink/STP/RSTP/MSTP/ERPS/LACP
- Support RIP,OSPF
- Support Power redundancy backup, Modular power supply, Modular fans supply
- Support ONT power failure alarm
Device Brief Information
Solution Display
The XG-PON system usually consists of the OLT at the office side, the ONU and the ODN at the user side, and adopts a point-to-multipoint network structure. The ODN consists of single-mode optical fibers and passive optical devices such as optical splitters and optical connectors. It provides the optical transmission medium for the physical connection between the OLT and ONU.
Hardware Specification
|
Attributes |
GP5810-16 |
|
Interface |
16*XG(S)-PON/GPON Combo port, 8*1000M Base-X SFP/8*10GE SFP+, 2*40G/100G QSFP28 |
|
Exchange Capacity |
880Gbps |
|
Forwarding Rate |
654.72Mpps |
|
Memory and Storage |
Memory：2GB, Storage：8GB |
|
MAC Address |
32K |
|
Packet Buffer |
72Mbit |
|
Management Port |
Console, MGMT |
|
PON |
Comply with ITU-T G.987/G.988 standard; Wavelength of GPON: 1490nm downstream and 1310nm upstream; Wavelength of XGPON: 1577nm downstream, 1270nm upstream; |
|
GPON: Downstream – 2.48832Gbps, Upstream – 1.24416Gbps; XGPON: Downstream – 9.95328Gbps, Upstream – 2.48832Gbps. XGSPON: Downstream – 9.95328Gbps, Upstream – 9.95328Gbps; |
|
|
GPON supports a maximum distance of 60KM logical distance, 20KM physical distance, and 20KM differential distance; XGPON supports a maximum distance of 100KM logical distance, 40KM physical distance, and 40KM differential distance; |
|
|
PON port total 1:256 Maximum spectral ratio, GPON 1:128, XGPON/XGSPON 1:128; |
|
|
Standard OMCI management function; Open to any brand of ONT; ONU batch software upgrade; PON module adapts to standard 20PIN SFP+ package module |
|
|
Environment Temperature |
Working Temperature：-10℃～55℃ Storge temperature：-40℃～70℃ |
|
Environment Humidity |
Relative Humidity: 5%~95%, non-condensing |
|
Environment Friendly |
RoHS |
|
Weight |
8KG |
|
Fan |
Modular fans supply (2) |
|
Power |
AC: 100～240V 47/63Hz; DC: -36V～-75V; |
|
Power Consumption |
150W |
|
Dimensions(W*D*H) |
440mm*320mm*44mm |
Product Interface
|
Label |
Connector Type |
Connector Description |
|
100G 1-2 |
QSFP28 |
Connect to external uplink equipment |
|
1G/10G 1-8 |
SFP |
Connect to external uplink equipment |
|
XGSPON COMBO 1-16 |
SFP+ |
XGS-PON COMBO service port |
|
MGMT |
RJ45 |
The out-band management port |
|
CONSOLE |
RJ45 |
The software debug port |
|
ALM |
RJ45 |
4*external alarm input |
|
TOD |
RJ45 |
1*1PPS+TOD input |
|
USB |
USB2.0,3.0 |
Example Export debugging log files |
LEDs Operating Status
The operation status of GP5810 can be determined by using the front LED. The panel LED indicator will display the status of each interface. The meaning of LED is shown in the following table.
|
LEDs/Buttons |
Color |
Function |
Description |
|
|
SYS |
Green |
System running status |
Green OFF |
The device is not running or power off. |
|
Green Flash |
The device is running normally. |
|||
|
MGMT |
Green |
Port status |
ON |
The link is properly connected (link up) and in action |
|
OFF |
The link is interrupted (link down). |
|||
|
ALM |
Red |
Critical alarms |
ON |
Critical alarms are reported for the card. |
|
OFF |
No critical alarm is reported for the card. |
|||
|
TOD |
Green |
Port status |
ON |
The link is properly connected (link up) and in action |
|
OFF |
The link is interrupted (link down). |
|||
|
FAN |
Green |
Fan running status |
ON |
FAN is running normally. |
|
OFF |
FAN is running abnormally. |
|||
|
PWR 1-2 |
Green |
Power status |
ON |
The AC/DC power module is normal. |
|
OFF |
The AC/DC power module faulty or unavailable Note: PWR1 indicates the left power card, and PWR2 indicates the right power card. |
|||
|
USB |
Green |
Link status |
ON |
Insert USB flash drive |
|
OFF |
NO insert USB flash drive |
|||
|
100GE 1-2 |
Green |
Port status |
ON |
The link is properly connected (link up) and in action |
|
OFF |
The link is interrupted (link down). |
|||
|
1G/10G 1-8 |
Green |
Port status |
ON |
The link is properly connected (link up) and action |
|
OFF |
The link is interrupted (link down). |
|||
|
PON1~16 |
Green |
PON port status |
ON |
At least one ONU has been successfully registered. |
|
OFF |
No ONU has been successfully registered. |
|||
|
RST |
N/A |
Reset button |
Long press on the RST button for to restart the equipment. |
|
Plug-In Units
On the rear panel of the OLT, there are two slots for Power Supply Unit (PSU). The mounting slots can be equipped with DC or AC type PSUs. The different type of PSUs can be equipped into the OLT. The below shows AC and DC type of power supply modules Two PSUs, for supplying redundancy, dual PSUs have to be installed at a system.
The power supply unit (PSU) feeds the proper power voltage to the base board of OLT. Two PSUs are possible to be mounted into rear of the chassis and it can be DC or AC type of PSU. Therefore, you need to decide to choose proper power supply unit according to installation environment.
The power connector (AC and DC type) for main power supply is located on the rear panel of the PSU. For redundant power feeding, the second PSU has to be used.
The below shows the electrical characteristics of the OLT：
|
Characteristic |
GP5810-16 |
|
Nominal DC power supply |
DC: 36V～75V; |
|
Nominal AC power supply |
AC:100～240V; 47/63Hz |
|
FAN |
The temperature starts at 0 degrees and rotates at 30% speed (about 3900 RPM), and the speed increases by 0.78%x13000 rpm for every 1℃ increase. |
|
AC Rated power of power supply |
220W |
|
DC Rated power of power supply |
220W |
FAN Unit
The OLT provides 2 fan unit slots on the rear panel. This plug-in unit internally consists of 2 fans. User can insert fan unit to a fan slot by slowly adjusting them to fit into the slot guidance. The air flows from the front side inlet to the rear side outlet.
Software Specification
|
Attributes |
GP5810-16 |
|
PON |
Support N1/N2/E2 XG-PON or XGS-PON optical module Support N1/B+, N2/C+, E2/D Combo optical modules SN / SN + Password ONU authentication ONU optical power monitoring Rogue ONU detection |
|
VLAN |
Support 4K VLAN Support VLAN based on port, MAC and protocol Support dual Tag VLAN, port-based static Q-in-Q and flexible Q-in-Q |
|
MAC |
128K Mac address Support static MAC address setting Support black hole MAC address filtering Support port MAC address limit |
|
Ring Network Protocol |
Support STP/RSTP/MSTP Support ERPS Ethernet ring network protection protocol Support Loopback-detection port loopback detection |
|
Port Control |
Support two-way bandwidth control Support port storm suppression Support 9K Jumbo ultra-long frame forwarding |
|
Port Aggregation |
Support static link aggregation Support dynamic LACP Each aggregation group supports a maximum of 8 ports |
|
Mirroring |
Support port mirroring Support stream mirroring |
|
ACL |
Support standard and extended ACL Support ACL policy based on time period Provide flow classification and flow definition based on IP header information such as source/destination MAC address, VLAN, 802.1p, ToS, DSCP, source/destination IP address, L4 port number, protocol type, etc. |
|
QoS |
Support flow rate limiting function based on custom business flow Supports mirroring and redirection functions based on custom business flows Support priority marking based on custom service flow, support 802.1P, DSCP priority Remark capability Support port-based priority scheduling function, support queue scheduling algorithms such as SP/WRR/SP+WRR |
|
VLAN |
Support 4K VLAN Support VLAN based on port, MAC and protocol Support dual Tag VLAN, port-based static Q-in-Q and flexible Q-in-Q |
|
Safety |
Support user hierarchical management and password protection Support IEEE 802.1X authentication Support Radius&TACACS+ authentication Support MAC address learning limit, support black hole MAC function Support port isolation Support broadcast message rate suppression Support IP Source Guard Support ARP flood suppression and ARP spoofing protection |
|
Layer3 Routing |
Support ARP learning and aging Support static route Support dynamic route RIP/OSPF/BGP/ISIS Support VRRP |
|
System management |
CLI,Telnet,WEB,SNMP V1/V2/V3,SSH2.0 Support FTP, TFTP file upload and download Support SNTP Support LLDP neighbor device discovery protocol Support RFC 3164 Syslog Support Ping and Traceroute |
Connector Specifications
The OLT provides standardized interfaces, thus facilitating rapid and trouble-free integration into the existing network infrastructures.
PON Interfaces
The OLT contains 16 XGS-COMBO PON interface ports for SFP+ modules and below table is available .
XGS COMBO PON module list.
|
1 |
XGS-COMBO PON OLT SFP+ . 20 PIN DFB . Single fiber bi-directional data links with downstream 9.953Gbps and 2.488Gbps . Single fiber bi-directional data links with upstream 9.953G/2.488Gbps and 1.244Gbps . 0 to 70°C operating case temperature . SFP+ package with SC Receptacle connector . High power 1577nm EML and 1490nm DFB transmitter . High sensitivity 1270nm/ 1310nm APD-TIA . Support 20km transmission distance with SMF . RoHS compliance |
Network Interfaces
The OLT optical interface ports for SFP/SFP+ modules and below table is available SFP/SFP+ module list.
|
Index |
SFP/SFP+ Module Description |
|
1 |
- Wavelength: 850 nm / Distance: 550 m / Mode: multi-mode - Connector: LC / Data rate: 1.25Gbit/s / Core type: Dual Core - Operating Temperature: 0 °C - 70 °C |
|
2 |
-. Wavelength: 1310nm / Distance: 5km / Mode: single-mode -. Connector: LC / Data rate: 1.25Gbit/s / Core type: Dual Core -. Operating Temperature: 0 °C – 70 °C |
|
3 |
- Wavelength: 1310 nm / Distance: 10 km / Mode: single-mode - Connector: LC / Data rate: 1.25 Gbit/s / Core type: Dual Core - Operating Temperature: 0 °C – 70 °C |
|
4 |
- Wavelength: 1310 nm / Distance: 15 km / Mode: single-mode - Connector: LC / Data rate: 1.25 Gbit/s / Core type: Dual Core - Operating Temperature: 0 °C – 70 °C |
|
5 |
- Wavelength: 1310 nm / Distance: 20 km / Mode: single-mode - Connector: LC / Data rate: 1.25 Gbit/s / Core type: Dual Core - Operating Temperature: 0 °C - 70 °C |
|
6 |
- Wavelength: 1310 nm / Distance: 40 km / Mode: single-mode - Connector: LC / Data rate: 1.25 Gbit/s / Core type: Dual Core - Operating Temperature: 0 °C - 70 °C |
|
7 |
- Wavelength: 850nm / Distance: 300m / Mode: Multimode - Connector: LC / Data rate: 10.3125 Gbit/s / Core type: Dual Core - Operating Temperature: 0°C ~ 70 °C - 10GBASE-SR (10G) |
|
8 |
- Wavelength: 850nm / Distance: 300m / Mode: Multimode - Connector: LC / Data rate: 10.3125 Gbit/s / Core type: Dual Core - Operating Temperature: 0°C ~ 70 °C - 1000BASE-SX (1G), 10GBASE-SR (10G) |
|
9 |
- Wavelength: 1310nm / Distance: 10Km / Mode: Single mode - Connector: LC / Data rate: 10.3125 Gbit/s / Core type: Dual Core - Operating Temperature: 0°C ~ 70 °C - 10GBASE-LR (10G) |
|
10 |
- Wavelength: 1550nm / Distance: 40Km / Mode: Single mode - Connector: LC / Data rate: 10.3125 Gbit/s / Core type: Dual Core - Operating Temperature: 0°C ~ 70 °C - 10GBASE-ER (10G) |
|
11 |
- Wavelength: 1310nm / Distance: 70Km / Mode: Single mode - Connector: LC / Data rate: 10.3125 Gbit/s / Core type: Dual Core - Operating Temperature: 0°C ~ 70 °C - 10GBASE-ZR (10G) |
|
12 |
- Wavelength: 850nm / Distance: 100m / Mode: MMF - Connector: MMF Data rate: 100 Gbit/s / Core type: Dual Core - Operating Temperature: 0°C ~ 70 °C 100GBASE-SR4 |
Purchase Info
|
Product Name |
Product Description |
|
GP5810-16 |
16*XG(S)-PON/GPON Combo port, 8*1000M Base-X SFP/8*10GE SFP+, 2*40G/100G QSFP28 |
Hot Tags: gp5810-16 pizza box 10g xg(s)-pon combo olt, China gp5810-16 pizza box 10g xg(s)-pon combo olt manufacturers, factory, 4 pon, HGP5810 XG S PON Combo OLT, 8 port olt, 16 port gpon olt, compatible onu olt, olt device
You Might Also Like
Send Inquiry